WEKO3
アイテム
研削加工におけるステンレス鋼の表面性状について(第1報) : 平面研削における一般砥石とCBNホイールとの比較
http://hdl.handle.net/10232/11481
http://hdl.handle.net/10232/11481f857447a-6c8a-4814-a89a-dd2ffd45ebba
| 名前 / ファイル | ライセンス | アクション |
|---|---|---|
AN00040363_v30_p45-52.pdf (2.8 MB)
|
|
| Item type | 紀要論文 / Departmental Bulletin Paper(1) | |||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 公開日 | 2015-06-05 | |||||||||||||||||
| タイトル | ||||||||||||||||||
| タイトル | 研削加工におけるステンレス鋼の表面性状について(第1報) : 平面研削における一般砥石とCBNホイールとの比較 | |||||||||||||||||
| タイトル言語 | ja | |||||||||||||||||
| タイトル | ||||||||||||||||||
| タイトル | Surface Quality in the Grinding of Stainless Steels (1st Report) : Comparison with 19A, GC and CBN Abrasive Wheel in Surface Grinding | |||||||||||||||||
| タイトル言語 | en | |||||||||||||||||
| 著者 |
田中, 秀穂
× 田中, 秀穂
× 是枝, 賢一
× 劉, 英
|
|||||||||||||||||
| 言語 | ||||||||||||||||||
| 言語 | jpn | |||||||||||||||||
| 資源タイプ | ||||||||||||||||||
| 資源タイプ識別子 | http://purl.org/coar/resource_type/c_6501 | |||||||||||||||||
| 資源タイプ | departmental bulletin paper | |||||||||||||||||
| アクセス権 | ||||||||||||||||||
| アクセス権 | open access | |||||||||||||||||
| アクセス権URI | http://purl.org/coar/access_right/c_abf2 | |||||||||||||||||
| 要約 | ||||||||||||||||||
| 内容記述タイプ | Other | |||||||||||||||||
| 内容記述 | Microcracks different type of usual grinding crack are generated in grinding of stainless steel according to the types of the material. As they generate at depth of about 2-20 μm from ground surface nearly pararell to the surface, and are very microscopic, they cannot be found possibly by naked eye. Therefore, it is apprehended that they lead to grave defect for actual products. In this paper, to examine the effects in surface grinding on the ground surface quality, especially on the generating mechanism of the microcracks, 3 types of abrasive wheel were employed. The effects of 2 types of general abrasive wheels-19A and GC abrasive wheels- and CBN wheel that has attracted lately special interests as a beneficial wheel from a standpoint of ground surface quality on that quality were examined. Following results were obtained. 1) Constraint conditions of stresses by grinding force were infirm, because of the readiness of temperature rise and elastic deformation due to small size of works. Therefore, ''microcracks'' were not observed in all grinding conditions employed. 2) Grinding surface temperature by CBN abrasive wheel is far lower than general abrasive (19A, GC) wheel. 3) Therefore, actual depth of cut is greater than theoretical one whereas do not occur like that in CBN abrasive wheel. | |||||||||||||||||
| 内容記述言語 | en | |||||||||||||||||
| 収録雑誌名 |
ja : 鹿児島大学工学部研究報告 en : The research reports of the Faculty of Engineering, Kagoshima University 巻 30, p. 45-52, 発行日 1988-11 |
|||||||||||||||||
| 作成日 | ||||||||||||||||||
| 日付 | 1988-11 | |||||||||||||||||
| 日付タイプ | Issued | |||||||||||||||||
| ISSN | ||||||||||||||||||
| 収録物識別子タイプ | PISSN | |||||||||||||||||
| ISSN | 0451212X | |||||||||||||||||
| NII書誌ID（雑誌） | ||||||||||||||||||
| 収録物識別子タイプ | NCID | |||||||||||||||||
| NC ID | AN00040363 | |||||||||||||||||
| 出版タイプ | ||||||||||||||||||
| 出版タイプ | VoR | |||||||||||||||||
| 出版タイプResource | http://purl.org/coar/version/c_970fb48d4fbd8a85 | |||||||||||||||||
| NDC | ||||||||||||||||||
| 主題Scheme | NDC | |||||||||||||||||
| 主題 | 532 | |||||||||||||||||
| 公開者・出版者 | ||||||||||||||||||
| 出版者 | 鹿児島大学 | |||||||||||||||||
| 出版者言語 | ja | |||||||||||||||||
| 公開者・出版者 | ||||||||||||||||||
| 出版者 | Kagoshima University | |||||||||||||||||
| 出版者言語 | en | |||||||||||||||||
