WEKO3
アイテム
管端スピニング加工における鋼管の定圧加工による成形性について
http://hdl.handle.net/10232/12841
http://hdl.handle.net/10232/12841f89c38d0-89d8-4fd0-b3e7-c76b23d1da9c
| 名前 / ファイル | ライセンス | アクション |
|---|---|---|
AN00040363_v14_p19-27.pdf (12.2 MB)
|
|
| Item type | 紀要論文 / Departmental Bulletin Paper(1) | |||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 公開日 | 2015-06-18 | |||||||||||||||||
| タイトル | ||||||||||||||||||
| タイトル | 管端スピニング加工における鋼管の定圧加工による成形性について | |||||||||||||||||
| タイトル言語 | ja | |||||||||||||||||
| タイトル | ||||||||||||||||||
| タイトル | THE WORKABILITIE OF A STEEL MATERIAL FOR THE TUBE END SPINNING OPERATED UNDER A CERTAIN (CONSTANT) THRUST PRESSURE | |||||||||||||||||
| タイトル言語 | en | |||||||||||||||||
| 著者 |
岡村, 俊一
× 岡村, 俊一
× 田中, 秀穂
× 南, 俊美
|
|||||||||||||||||
| 言語 | ||||||||||||||||||
| 言語 | jpn | |||||||||||||||||
| 資源タイプ | ||||||||||||||||||
| 資源タイプ識別子 | http://purl.org/coar/resource_type/c_6501 | |||||||||||||||||
| 資源タイプ | departmental bulletin paper | |||||||||||||||||
| アクセス権 | ||||||||||||||||||
| アクセス権 | open access | |||||||||||||||||
| アクセス権URI | http://purl.org/coar/access_right/c_abf2 | |||||||||||||||||
| 要約 | ||||||||||||||||||
| 内容記述タイプ | Other | |||||||||||||||||
| 内容記述 | The experimental exminations were performed on the workabilities of steel tube stock, STKM 13A, for the tube end spinning using the tube end spinning machine which was manufactured on trial recently and on which the tube stock was feeded into the revolving die under a certain (constant) thrust pressure by using the hydraulic piston. According to the experimental results, it was cleared that the forming limit of a steel material for the tube end spinning is defined by the seisure. So, in this report, the operating conditions of spinning that do not cause seisure during the forming process, were examined. The obtained results are as follows : 1. The forming limit defined by seisure is decreased according to increment of die revolution and conical angle of die and is increased according to increment of ram pressure. 2. Under a certain die revolution, seisure is occored at the approximately same time and this is not depend on ram pressure. 3. The time to seisure is shorter according to increment of conical angle of die. 4. The torque as a working resistance is not depend on ram pressure. |
|||||||||||||||||
| 内容記述言語 | en | |||||||||||||||||
| 収録雑誌名 |
ja : 鹿児島大学工学部研究報告 en : The research reports of the Faculty of Engineering, Kagoshima University 巻 14, p. 19-27, 発行日 1972-09 |
|||||||||||||||||
| 作成日 | ||||||||||||||||||
| 日付 | 1972-09 | |||||||||||||||||
| 日付タイプ | Issued | |||||||||||||||||
| ISSN | ||||||||||||||||||
| 収録物識別子タイプ | PISSN | |||||||||||||||||
| ISSN | 0451212X | |||||||||||||||||
| NII書誌ID（雑誌） | ||||||||||||||||||
| 収録物識別子タイプ | NCID | |||||||||||||||||
| NC ID | AN00040363 | |||||||||||||||||
| 出版タイプ | ||||||||||||||||||
| 出版タイプ | VoR | |||||||||||||||||
| 出版タイプResource | http://purl.org/coar/version/c_970fb48d4fbd8a85 | |||||||||||||||||
| NDC | ||||||||||||||||||
| 主題Scheme | NDC | |||||||||||||||||
| 主題 | 566 | |||||||||||||||||
| 公開者・出版者 | ||||||||||||||||||
| 出版者 | 鹿児島大学 | |||||||||||||||||
| 出版者言語 | ja | |||||||||||||||||
| 公開者・出版者 | ||||||||||||||||||
| 出版者 | Kagoshima University | |||||||||||||||||
| 出版者言語 | en | |||||||||||||||||
