WEKO3
アイテム
研削仕上げ面粗さに関する研究 (仕上げ研削における，同一点研削回数について)
http://hdl.handle.net/10232/10643
http://hdl.handle.net/10232/1064373a905aa-6a9f-4e5b-852a-d78f21fd8ae3
| 名前 / ファイル | ライセンス | アクション |
|---|---|---|
AN00040363_v2_p75-81.pdf (3.1 MB)
|
|
| Item type | 紀要論文 / Departmental Bulletin Paper(1) | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 公開日 | 2015-06-24 | |||||||||||||
| タイトル | ||||||||||||||
| タイトル | 研削仕上げ面粗さに関する研究 (仕上げ研削における，同一点研削回数について) | |||||||||||||
| タイトル言語 | ja | |||||||||||||
| タイトル | ||||||||||||||
| タイトル | Studies on the roughness of grind finish surfaces | |||||||||||||
| タイトル言語 | en | |||||||||||||
| 著者 |
中島, 繁
× 中島, 繁
× 田中, 秀穂
|
|||||||||||||
| 言語 | ||||||||||||||
| 言語 | jpn | |||||||||||||
| 資源タイプ | ||||||||||||||
| 資源タイプ識別子 | http://purl.org/coar/resource_type/c_6501 | |||||||||||||
| 資源タイプ | departmental bulletin paper | |||||||||||||
| アクセス権 | ||||||||||||||
| アクセス権 | open access | |||||||||||||
| アクセス権URI | http://purl.org/coar/access_right/c_abf2 | |||||||||||||
| 要約 | ||||||||||||||
| 内容記述タイプ | Other | |||||||||||||
| 内容記述 | In order to obtain well finished surfaces by grinding Operation，it is of course desirable to repeat grinding several times without giving cuttilng depths on the same point of the works. The problem here is the extent to which the grinding operation should be done for the improvement of the working efficiency. Generally speaking， the finish surfaces would not be improved above some grade according to the vibration of grinding machine and other various reasons. The authors studied on the roughness with several sorts of materials (ST180, SF54, SS34，FC15 and FC20) to be ground examining the influences of those reasons upon the finish surface. As obviously shown in the graph，the roughness is in general indicated to be similarly stational though accompanying more or less differrence in quantitative measurement. Up to 20 times of grinding，the influence of them was revealed considerable, while at the number above 20 times the roughness turned out showing no improvement. The idea that the increased number would result good surfaces was found to be wrong, and also it was revealed to be against the working efficiency. Accordingly the authors conclude their research results as follows：- (1)When the same point of the material applied is given the cutting depth, the depths should be greatly affected, accordingly in that occasion the initial cutting should be made in a small size．(2)The number of grinding on the same point is to be quite enough applying within some 40 times. |
|||||||||||||
| 内容記述言語 | en | |||||||||||||
| 収録雑誌名 |
ja : 鹿児島大学工学部研究報告 en : The research reports of the Faculty of Engineering, Kagoshima University 巻 2, p. 75-81, 発行日 1962-09 |
|||||||||||||
| 作成日 | ||||||||||||||
| 日付 | 1962-09 | |||||||||||||
| 日付タイプ | Issued | |||||||||||||
| ISSN | ||||||||||||||
| 収録物識別子タイプ | PISSN | |||||||||||||
| ISSN | 0451212X | |||||||||||||
| NII書誌ID（雑誌） | ||||||||||||||
| 収録物識別子タイプ | NCID | |||||||||||||
| NC ID | AN00040363 | |||||||||||||
| 出版タイプ | ||||||||||||||
| 出版タイプ | VoR | |||||||||||||
| 出版タイプResource | http://purl.org/coar/version/c_970fb48d4fbd8a85 | |||||||||||||
| NDC | ||||||||||||||
| 主題Scheme | NDC | |||||||||||||
| 主題 | 532 | |||||||||||||
| 公開者・出版者 | ||||||||||||||
| 出版者 | 鹿児島大学 | |||||||||||||
| 出版者言語 | ja | |||||||||||||
| 公開者・出版者 | ||||||||||||||
| 出版者 | Kagoshima University | |||||||||||||
| 出版者言語 | en | |||||||||||||
